Price:
$7050
Product ID:
DES-ACHX4-482436
Lead Time:
Contact Us to inquire about lead times
Return Policy:
14 days for a full refund

Product Specifications

Inside Dimensions (inch):
48 W X 24 D X 36 H
Product Dimensions (inch):
52 W X 30 D X 40 H
Tolerance (inch):
+/- 0.125
Chamber Material:
Clear Cast Acrylic
Lid Material:
Clear Cast Acrylic
Door Seal:
Air Tight (Buna-N O-Ring)
Hygrometer Accuracy :
+/- 5%RH
Thermometer Accuracy :
+/- 1% Deg C

Features

Clear Acrylic Desiccator Cabinet
1 perforated shelf per box
1 gas IN port 1/4 NPT (blanked off) per box
1 gas OUT port 1/4 NPT (blanked off) per box
digital hygrometer per box
digital thermometer per box
dry, dust-free, and oil-free environment

Description

There is a total of four (4) desiccator boxes in this system ? the boxes are arranged in two rows and two columns (2x2 configuration), bringing the summarized dimensions to 48-inch-wide, 24-inch-deep by 36 inch high. Each single desiccator box has the inside dimensions of 24-inch Wide, 24-inch Deep, and 18-inch High. All three desiccators are fully assembled and are ready to go. Each comes with one fully removable perforated shelf, a digital hygrometer, two gas ports that are 1/4 inch NPT and plugged, and four door clamps. These are air tight boxes which means that as soon as you close the door and engage the clamps, they become hermetically sealed.

We construct our desiccator cabinets the same way we construct any of our products which means that these desiccator boxes are robustly designed and quality manufactured to consistently perform and meet your needs. These two dry boxes will enable you to store any component that requires dry storage such as anhydrous and hygroscopic biological, chemical compound, or electronic assemblies. These can be used for long term and short-term storage of laboratory samples as well. Desiccator cabinets will reduce humidity/oxygen within the box. Desiccators are air tight containers envisioned to store samples shielded from dust and contamination and/or in a low humidity and in some cases a low oxygen environment.

Please note that this desiccator is not intended to be pressurized, if you required a vacuum chamber or a pressure chamber click on the link. Also note that acrylic material is hygroscopic meaning that it will absorb and transport humidity. Say you are operating in a relatively high humidity environment (80%) and say that you bring the humidity inside this desiccator cabinet to below 20%. Due to the nature of acrylic, the humidity will travel through the walls and slowly increase the humidity until it gets to a steady state. If no further action is taken, the humidity inside the desiccator cabinet will equalize with the outside within a couple of hours. In order to keep the humidity at a certain level, you will have to monitor it or control it as we mentioned before, acrylic is hygroscopic.

WAIT! Take a look at similar Items you may likeā€¦

We make Robustly Designed and Quality Engineered Systems. Check out some of our other items we carry that you can combine/integrate with your systems or projects.

Vacuum Chamber and Pump Systems
Our Vacuum Chamber and pump systems are fully setup and ready to go. What you get is a vacuum chamber, a vacuum pump, and connection hardware. We carry acrylic or metallic vacuum chambers and a whole range of vacuum pumps from Rotary Vane, Piston, or Venturi. What type of vacuum chamber and pump system you want depends on your project requirement, budget, and other specifications.
Altitude Simulation Controller Instruments
An Altitude simulation Controller is type of vacuum controller that simulates a certain altitude because altitude can be derived from vacuum levels. An altitude simulation controller will enable you to hold your vacuum level at a certain altitude equivalent of testing, run an altitude vs time profile, or rate of change of altitude vs. time. Further options include a vacuum pump relay that will control when the vacuum pump turns on and a vacuum valve.
Our Work: Bubble Leak Testing System with a Dry off Sink used for Leak Testing Large Bags
How do you leak test Large Food Bags? This is the same question a Large Food and Beverage Processor had asked themselves because they had need for a bubble leak testing system which could be used to detect presence of leaks in their large bags. Their requirements were to test several sized bags with the largest bag being 24 inches Wide by 12 inch Deep by 9 inches High. In addition to the bubble leak testing system, they also needed a way to dry the bags after the test.
Related Articles: Force Decay Leak Testing
Force Decay Leak Testing is a very popular quantitative leak testing method used to quality test package and product integrity due to its ability to detect small leaks which cannot be seen through visual inspection. In this method, the test specimen is internally inflated by either internal pressurization or vacuum force. The inflated test specimen will, in turn, apply a force on a pressure transducer. Finally, the change in force applied by the inflated specimen over a specified time is observed.

Additional Comments

1. Depiction: We go above and beyond to represent our products the best we can, but all images are for reference only. If you want the exact dimensions of a product, please refer to the product drawing. If the drawing is not present, please contact us.

2. Discount: If you are ordering more than one item you will qualify for a discount, contact us for more details. No discount will be given after you have ordered and then realized you can get a discount. We put in a lot of effort writing this and we don`t reward failure to read our descriptions. However, since we are nice guys, we will give you a discount on your next order.

3. Shipping: The shipping rates are for the lower 48 states only; additional shipping charges apply to Alaska, Hawaii, and international orders. Keep in mind that international order will also be subject to duty and other charges.

4. Products: Our products are built-to-order; therefore, your product can be customized, but you must let us know beforehand. The pricing, shipping terms, and lead time apply to orders of less than three (3) items. If you are ordering more than 3 items, you should contact us to discuss your quote.

5. Return Policy: 14 days on all standard products. We stand 100% behind our products. If there was a mistake on our part, you will be refunded 100% of your money including shipping. If the mistake was on your part or you decided that you didn`t want it after all, you will pay for shipping and we will fully refund rest of your money. Chamber must be insured during return shipping for the price that you paid for and in a non-damaged condition. Return Policy does NOT apply to custom items, jobs, or products. If you have asked us to modify any of our standard products, you will not be able to return your item.