Price:
$16200
Product ID:
LEAK-BOXEL-302020
Lead Time:
Contact Us to inquire about lead times
Return Policy:
14 days for a full refund

Additional Vacuum Bubble Leak Tester Images

Please take a look at additional product images of our ASTM D3078 Bubble Leak Testing System. All our products can be modified and customized to your requirements. Please contact us if you are looking for a custom Bubble Leak Testing System.

Cylindrical Vacuum Chamber ASTM D3078 Bubble Leak Tester


The Only Vacuum Bubble Leak Test Chamber robustly designed and quality manufactured
to consistently perform and meet your needs!

Product Specifications

Vacuum Rating:
0.075 Torr (75 micron, dry)
Vacuum Loss Rate
5.25 Torr (0.2 inHg) in 24 hours
Chamber Inside Dimensions (inch):
30 Wide, 20 Deep, 20 High
Tolerance (inch)
+/- 0.125
Chamber Material:
Clear Cast Acrylic
Lid Material:
Clear Cast Acrylic
Seal:
Buna-N O-Ring
Approximate Volume:
12000 cubic inch - 52 Gallon - 197 Liters

Features

Vacuum Gauge
Vacuum Regulator Adjustment Valve
Vent Valve 1/4 NPT
Vacuum Valve 1/4 NPT
Water Drain Valve
Package Restrainin Mesh
Vacuum Pump Protection Valve
Two Lid Clamps
Spring Supported Lid
One Year Safe Buyback Guarantee

Description

This bubble leak testing system is fully setup and ready to go right out of the box. The inside dimensions of the test chamber are: 30 inch wide, 20 inch deep, and 20 inch tall. It is powered by Electrical Vacuum Pump 12CFM which is included in this system. Also included with the bubble emission testing system are a vacuum regulator, vacuum valve, a venting valve, a vacuum gauge, a water drain valve, package restrain mesh, two (2) 1/4 inch OD tube feed through ports, a spring supported lid, and a vacuum trap (to keep pump free of moisture coming from the chamber).

This Bubble Leak Testing System (also known as the Bubble Emission Testing Equipment) is used to test the seal integrity sealed packages, such as medical packages. This procedure is performed by submersing the fully sealed specimen into a tank of water and pulling a vacuum in order to create a pressure difference between the inside of the pouch and the outside. If the package integrity is compromised, this pressure difference will begin to drive the air out of the package and bubbles will start to emit from the pouch. The location of bubble emission points to the leak.

A bubble leak testing system is by far the most economical and practical method for performing medical package testing and detecting pouch leaks. Your package integrity test can be performed in 30 seconds or less.

Sanatron Quality Testing Systems are much better than a Recall or an Unplanned Corrective Action

If you think that you do not have the time or the resources to implement a proper Quality Control Program, then you certainly will not have the time or the resources for unprompted Corrective Actions after Faulty or Leaking Products have reached your Customers.

Imagine having to explain to your team, your superiors, and your customers as to why there are so many quality defects. Imagine having to explain what you could have done to prevent it. Imagine dealing with field alerts, recalls, or having to contend with your auditors as to why you don’t have a Quality Control or Leak Testing Procedure in place.

Fortunately, our Vacuum Bubble Leak Testing Systems will allow you to produce Great Products and will help you to perform the following Test Protocols:

ASTM D3078 Standard Test Method for Determination of Leaks in Flexible Packaging by Bubble Emission
ASTM D4169 Standard Practice for Performance Testing of Shipping Containers and Systems
ASTM D4991 Standard Test Method for Leakage Testing of Empty Rigid Containers by Vacuum Method
ASTM D5094 Standard Test Methods for Gross Leakage of Liquids from Containers with Threaded or Lug-Style Closures
ASTM D6653 Standard Test Methods for Determining the Effects of High Altitude on Packaging Systems by Vacuum Method
ASTM E515 Standard Practice for Leaks Using Bubble Emission Techniques
MIL-STD-810 MIL Standard Immersion Test 810G
MIL-STD-3010C MILITARY STANDARD: TEST PROCEDURES FOR PACKAGING MATERIALS.
FED-STD-101–Test Procedure for Packaging Materials: Method 3028, Method 5009
AIAA 2000-3735 Aerospace Leak Test Requirements Such as the Detecting Gross Leaks

Do things right the first time! Everyone will benefit! Get your Quality Leak Testing System. Contact Us now.

You may be interested in some of our other items

Our clients prefer to work with us because we are Experts in Custom Fabrication (especially Polymer Fabrication). You should check out some of our other items we carry; click on the links below.

Acrylic Pressure and Vacuum Chambers
Acrylic Pressure and Vacuum Chambers are Pressure chambers that are capable of vacuum ratings that are the same vacuum rating of acrylic vacuum chambers. Keep in mind that Acrylic Pressure and Vacuum Chambers have a pressure limit of 15PSIG
Liquid and Gas Vacuum Feedthroughs
A Liquid and Gas Vacuum Feedthroughs are tubes that will allow you to run liquid or gas into your vacuum chamber without contaminating the vacuum levels or vacuum chamber in general. Say you are looking to run a coolant into the vacuum chamber and cool a component you are testing. You can simply install a liquid and gas vacuum feedthrough are run your coolant towards your test specimen.
Our Work: Vacuum Testing of Lithium Ion Batteries, Thin Film, Fuel Cells, Supercapacitors, and Nano materials
This vacuum chamber is a modification to our basic acrylic vacuum chamber 12 inch, removable lid model; except that our customer requested additional ports and electrical feed-through for testing of electrical equipment under vacuum. You know, I wish we would have asked them for more details on what they were doing with this chamber; their short and concise answer was that they were using our chamber to perform scientific work on the subjects of: lithium ion batteries, thin films, fuel cells, super-capacitors, and nano-materials testing in a vacuum environment.
Related Articles: Force Decay Leak Testing
Force Decay Leak Testing is a very popular quantitative leak testing method used to quality test package and product integrity due to its ability to detect small leaks which cannot be seen through visual inspection. In this method, the test specimen is internally inflated by either internal pressurization or vacuum force. The inflated test specimen will, in turn, apply a force on a pressure transducer. Finally, the change in force applied by the inflated specimen over a specified time is observed.

Additional Comments

1. Depiction: We go above and beyond to represent our products the best we can, but all images are for reference only. If you want the exact dimensions of a product, please refer to the product drawing. If the drawing is not present, please contact us.

2. Discount: If you are ordering more than one item you will qualify for a discount, contact us for more details. No discount will be given after you have ordered and then realized you can get a discount. We put in a lot of effort writing this and we don`t reward failure to read our descriptions. However, since we are nice guys, we will give you a discount on your next order.

3. Shipping: The shipping rates are for the lower 48 states only; additional shipping charges apply to Alaska, Hawaii, and international orders. Keep in mind that international order will also be subject to duty and other charges.

4. Products: Our products are built-to-order; therefore, your product can be customized, but you must let us know beforehand. The pricing, shipping terms, and lead time apply to orders of less than three (3) items. If you are ordering more than 3 items, you should contact us to discuss your quote.

5. Return Policy: 14 days on all standard products. We stand 100% behind our products. If there was a mistake on our part, you will be refunded 100% of your money including shipping. If the mistake was on your part or you decided that you didn`t want it after all, you will pay for shipping and we will fully refund rest of your money. Chamber must be insured during return shipping for the price that you paid for and in a non-damaged condition. Return Policy does NOT apply to custom items, jobs, or products. If you have asked us to modify any of our standard products, you will not be able to return your item.